It is used for standing training for patients with standing dysfunction such as paraplegia, cerebral palsy, and hemiplegia. It can also prevent or improve osteoporosis, pressure ulcers, reduced heart function and other diseases through standing training.
- Item No.:
- Series:
- Usage:
- Remark：
Construction
1. Foot Pedal
2. Side Bracket
3. Hip Pads And Straps
4. Strap Hanging Posts
5. Back Support Bracket
6. Back Bracket Adjustment Bolt
7. Back Support
8. Countertop
9. Countertop Bracket
10. Countertop Support Lifting Adjustment Bolt
11. Knee Brace
Data sheet
Size:
Adjustment Range:
✳Back support front and back adjustment range 15cm
Material:
✳Back support hip pad and leather surface
✳Internal polyurethane foam sponge one-time molding
✳Sprayed steel
✳Straps are sewn with high-strength canvas
Load:
✳ Footrest: 135kg
Instructions For Use
✳Remove or vertically place the back support, hip pad and straps, and the patient sits in a wheelchair and enters the front inner cavity of the standing frame. The rehabilitation therapist and nursing staff put the patient’s feet on the foot pedals with the knees close to the knee support.
✳The rehabilitation therapist and nursing staff help the patient stand up and use the hip pad and straps to help the patient stand completely.
✳Adjust the height of the table, chest support and back support to make the patient feel more comfortable. The patient’s arms are placed on the table. While doing standing training, finger function coordination training can be performed.
✳After the standing training, the rehabilitation therapist and nursing staff should first remove the back support, then loosen the hip pad and straps, help the patient sit in the wheelchair, and place the legs on the wheelchair pedals to move the wheelchair out of the standing frame.
Other Information
1. Product installation and debugging
✳When installing the product, please pay attention to the length of the screws inside.
✳Install the pedal and side bracket: first tighten the foot pedal, the horizontal steel pipe in front of the step board and the side brackets on both sides according to the position and direction of the screw holes.
✳Install the horizontal bracket: Because the horizontal bracket itself is a whole, you only need to fasten the horizontal bracket above the two side brackets with screws. Note that the horizontal bracket should be on the outside of the two side brackets during installation (refer to the finished product picture).
✳Install the knee bracket: Stretch out the plastic return-shaped accessories on the horizontal bracket, and fasten the knee bracket and the plastic return-shaped accessories with plastic handle screws. The knee bracket should be adjusted to a suitable state according to the patient’s own needs.
✳Install the strap hanging column: The hook is fixed to the bracket with screws.
✳Install the table: according to the screw holes under the table panel, tighten the table bracket with screws
✳Install the back support: insert the matching steel pipe under the table panel, tighten it with screws, and then put it into the back support. The back support adjustment bolt is used to adjust the back support forward and backward to play a tightening role.
✳Finally, hang the strap on the strap hanging column and adjust it to a suitable position.
Friendly reminder: When installing, you can refer to the above finished product picture for installation.
2. Precautions
✳Before using the standing frame, the rehabilitation therapist should check whether the equipment is placed on a flat ground, there should be no shaking, and read the product manual in detail, familiarize yourself with the performance, requirements and operation methods of the product, and perform an unloaded operation inspection on the product. The product can only be used when it is in good and normal condition.
✳Patients should conduct standing training with the help of rehabilitation therapists or professional nursing staff.
✳Standing training should follow the principle of “gradual progress” and gradually increase the training time.
✳When performing standing training, the hip straps used by patients must fit firmly and must not be loose.
3. Maintenance and care
✳All parts of the product should be kept clean and wiped gently with a clean soft cloth regularly.
✳The product can be transported by general means of transportation. It should be handled with care during transportation and should be protected from sun and rain. It is prohibited to mix it with pollutants.
✳The product should be stored in a dry, ventilated room without corrosive substances.